Aloah, with the topic because I do not really know much about it, I would like to know me, how I rüberbekomme data of my PC to my other PC. Following: There are a total of 14GB. I intend to the movies that I recorded of DVB-T circumcised. My old computer but here is so slow in such things, that even the smallest of the preview file (650MB) lasts forever. As the largest file is 4.5 GB big, I can not on a memory stick (do not store 1GB) and synonymous to dual DVD (8.5 GB) burn (because I have only one of them). How can I now herübertransportieren the data? I have DSL, both PCs are s.einem router, both have Windows 2000. One PC is directly s.Router via network cable, the other has W-LAN. Are not there any possibilities, eg to send it through the router? Or any cables, which I can tuck in both PCs? The problem is can only ever see of a PC the Picture, as used in analog monitor (a computer) as synonymous digital (other PC) will be. Merci
Antwort von Nightfly!:
"Lawrence" wrote:
... How can I now herübertransportieren the data? I have DSL, both PCs are s.einem router, both have Windows 2000. One PC is directly s.Router via network cable, the other has W-LAN. Are not there any possibilities, eg to send it through the router?
Yes there is, as you so you have PCs networked via the router. Guck doch einfach mal in your network environment or get into other computers. The prerequisite is that you - At your Netztwerkeinstellungen the same WORKGROUP s.besten have s.beiden computers - The appropriate directory / folder you were Released.
And then of just rüberschaufeln Calculator to Calculator.
Gruß, Nightfly!
Antwort von Nightfly!:
Possibility of directly using the IP address:
- Go to Start-> Run - Enter cmd - There ipconfig in the new window - Read the IP address (eg 192.168.1.2)
- Go to the other calculator to Start-> Run - I enter \ \ <IP>, with <IP> should be replaced by the above issue (eg \ \ 192.168.1.2)
If your firewall does not intercept all should now open a window where you can see the shared folders of the first PCs.
Gruß, Nightfly!
Antwort von soahC:
So book now if I understand correctly, indeed, depends s.router a pc via cable and the other is with w-lan, right? So rüberzujagen of probably a protracted affair 14.5 Gb over the Wi-Fi is!
My recommendation: Network cable out of the router directly and purely in the other PC! Then, as I said up IPs and Workgroup:
Workgroup: Right click on My Computer -> Properties -> Computer Name -> Change
Important is only that drinsteht the same workgroup on both computers
IPs: Start -> Settings -> Control Panel -> Internet and Network Connections -> Network Connections Right click on Local Area Connection -> Properties -> TCP / IP dial -> Properties Use the following IP: 192.168.10.5 (for the second computer 6) Subnet Mask: 255.255.255.0 (for second computer synonymous)
if (restart I have to believe in win2k) and you've got a nice 100 Mbit LAN connection of PC to PC Vorrausgesetzt (100Mbit network cards give her;)
Please correct if something is wrong!
Antwort von Lawrence:
Aloah, cool, thank you both for the answers! I'll try later times, and then provide reporting.
Antwort von Kanalratte:
Moin,
Quote:
Network cable out of the router directly and purely to another PC
Yes, but with the appropriate cable.
Quote:
Or any cables, which I can tuck in both PCs?
Crossed cable (crossover cable) to use.
Antwort von PowerMac:
Crossover cables you need today not possible afaik. Modern network cards can usually auto. At least, every Mac for five years;)
Antwort von Kanalratte:
@ PowerMac
The old Apple Mac. But can the new Intel-Microsoft-Mac? :-)
Antwort von soahC:
Need synonymous normal Intel PCs with Windows from ALDI (and indeed at least 5 years old) nichmehr!
Antwort von Kanalratte:
Quote:
My old computer but here is so slow in such things, that even the smallest of the preview file (650MB) lasts forever
I'm here considered synonymous of a very old PC. Not that he set up the peer-to-peer fails s.Kabel and it does not take into consideration.
Antwort von Lawrence:
Aloah, not tried, because lack of time, but I have an old crutch under 512MB of RAM and 1.8 GHz and as synonymous is still running all sorts of other stuff that pulls the premiere pretty down, as regards performance. Why this is so extremely lame but I honestly do not know synonymous.
Antwort von steveb:
with 14 GB will take about Network was a while. times, one should consider (if DVD) burner available, whether it 3-4 with DVD RW is not faster or more secure. in particular, then there is just a backup synonymous.
Antwort von Markus:
14 GB is 14,336 MB. A network with a transfer rate of 100 Mbit / s theoretically creates 14.3 MByte / s. It would take 14 GB of data transfer of 19.1 minutes.
Is it not so much. ;-)
Antwort von Nightfly!:
And if that should work with the cable, not yet:
Via cable to the router and then wireless.
Since then it takes 40-50 minutes.
Gruß, Nightfly!
Antwort von soahC:
Vorrausgesetzt he transfers the wlan with full 54 Mbps, which is NEVER the case!
Antwort von beiti:
Quote:
The problem is can only ever see of a PC the Picture, as used in analog monitor (a computer) as synonymous digital (other PC) will be.
That surely means that the Calculator are next to each other. Then with a direct network cable should be no problem.
Quote:
but I have an old crutch for the purposes of 512MB of RAM and 1.8 GHz and as synonymous is still running all sorts of other stuff that pulls the premiere pretty down, as regards performance.
For cutting of DVB-T, there are simpler ways than Premiere. I would file with ProjectX or PVAStrumento demux and then cut into MPEG2Schnitt or Cuttermaran. With my Athlon 800 Gingee the problem. See synonymous here: http://beitinger.de/sat/dvd_brennen.html
Antwort von steveb:
"Markus" wrote:
14 GB is 14,336 MB. A network with a transfer rate of 100 Mbit / s theoretically creates 14.3 MByte / s. It would take 14 GB of data transfer of 19.1 minutes.
Is it not so much. ;-)
My name is Teo Teo ..... in theory! :-)
Antwort von Markus:
Yes, yes, love the T (h eorie). Practically, I'll take a cup of coffee and did not look as closely at the clock. ;-)
This is something even of "high speed" - USB.
Antwort von Lawrence:
Aloah, not somehow works. I can not reposition the cable, because the partially by walls (breakthroughs go). If I'm doing as soahC describes it, although I can see the other PC, but here comes the prompt 'Connect As' and 'password'.
Antwort von beiti:
I) had recently suffered a similar problem (initial setting up a home network. Has proven to be very helpful while these instructions: http://www.pcwelt.de/know-how/hardware/31663/index1.html One must take quite a bit more time for it, but then you look neat and get through the PCs connected.
Antwort von soahC:
Ahh, okay. Maybe it's:
You need the folder (or folder, hdd ...), in which the files are released for an access from the network! Right click the folder -> Properties -> Sharing -> Share this folder on the Network!
Antwort von Lawrence:
Aloah, ok, I had forgotten to mention: It's released;) but is still not. Here's looking at me the instructions.
Antwort von prem:
do you see the shared folder? If so, then just try reinzuschieben times the data in these folders. if not, not because you know your password?
Antwort von Lawrence:
"Anonymous" wrote:
do you see the shared folder? If so, then just try reinzuschieben times the data in these folders. if not, not because you know your password?
No, I see the other PC, no more, no folder or something. But what sort of a password? ^ ^ I've got none.
Antwort von Lawrence:
Aloah, now I've tried everything again. LAN configured to assign IP, working on both PCs the same name, shared folder, but now appears that no access is done on the working group. I do not know if that is not even s.Router.
