Frage von Blackeagle123:
Hello,
have the ADVC 110 digital / analog. Have it connected via firewire s.PC.
If I were on the front mini-Firewire DV device (in this case a little)?, I hear the PC "pling" "pling" (the device is detected and then no longer recognized as if it was straight back and einsteckt herauszieht. This happens a few times!
If I use the Canopus via firewire? and the second camera s.einem Firewire input from the PC?, it will be recognized but in Premiere, I can not absorb. (Maybe there will be recognized on the yes no input signal is coming!)
Only when I use the Canopus concluding, I can without any problems of the camera directly via Firewire in Adobe Premiere recording.
How is it with you?
Drivers Are there any known problems? (My OS: WinXP SP2.)
Or is it more of a defect in the device? Cut is this afternoon and tomorrow, need urgent help because we are on the TV (which is wired with the) wanted to sift through.
Many greetings,
Constantin
Antwort von Kar.El.Gott:
Hi, Constantin
I suspect that only a DV device can operate s.einem Calculator. I have tried two cameras s.eine firewire card to hang, will not do. Only when I get a camera off, the other will be recognized.
The AVDC behaves indeed like a Camera ...
Antwort von Blackeagle123:
Hey,
that would be quite impractical because of the ADVC :-( has an extra firewire input s.der front and I thought that the device is internal to the signal there. But apparently it is only a Firewire hub?
Many greetings,
Constantin
Antwort von JMS Productions:
that would be quite impractical :-( But this is so. The PC can only have a FireWire device detect, 2 is not. I've also wondered, as I near the ADVC nor my Cam? wanted. Have already thought of the FireWire port or s.der Cam s.PC would be over, until I then draufkam what it is. As has already been said: The ADVC behaves himself as a "DV camera" ...
I think for your special projects you need FireWire card, I think, if at all possible ...
Antwort von RickyMartini:
1. Raw material of the Cam to HDD copy. This allows the analog output of the cam with a TV connected to the preview.
2. After dubbing the Canopus the Picture s.den TV deliver.
The only makes sense if the DV cam does not have - in analog, or material to be digitized.
Antwort von Christian27:
Hello,
So for me it is so:
I can s.den DV - In front s.ADVC-110? and then in the normal editing program (in my case, Canopus Edius) capture.
It is synonymous while the video s.den analog outputs (for TV) output ...
However, there's a small feature (at least for me so):
I have the first manual (also see directly) to "play" are, and then I can quite normal editing program in the control ...
If I was not first on the "Play" button is
no analog output preview!
Otherwise everything worked smoothly, but then in the editing program ...
Many greetings
Christian :-)
Antwort von Blackeagle123:
Hey,
as Christian described it, I understood it synonymous. Otherwise would be a Firewire input s.Canopus ADVC daft ...
Unfortunately for me the camera constantly recognized and not recognized and so go out and her. Christian, maybe you have any idea what's wrong? There are no drivers for it!
If tomorrow or the hotline at times of Canpus call. Today again the TV camera with wired and so captured. Then only the Canpus connected to the cut. Danke schon mal!
Many greetings,
Constantin
Antwort von Christian27:
Hello,
So there's drivers for the ADVC not only halt the standard Windows Firewire Drivers.
You have to jedenfall the ADVC-110 on the digital-in mode (blue light at Digital-In).
Then there are those still untem s.Gerät DIP switch.
This time you could be out which if it works then maybe ...
Or you could you look at the demo version of Edius download to test whether it is because you then synonymous with the works capture.
It is important as I have said that you have read the cam in play mode BEFORE you start editing program, or else refuses to allow the cam to the serial line.
Many greetings
Christian :-)
Antwort von Blackeagle123:
Hey,
the problem is that my Windows Camera constantly as new Firewire device detects and then does not recognize (remember the Windows sound, this "dingdong")!
In Schinttprogramm wirds not recognized ... a Picture, I do not synonymous, no preference whether the play mode or not!
The Digital In mode I have the.
What exactly do because they switch s.der bottom? I have a loose connection on DV in thought ...
I might try if recognized, when I inform him of the small Firewire connector s.der front s.PC?. According to manual it will s.PC way or recognized. Then perhaps I can at least rule out a defect. Many greetings,
Constantin
Antwort von Christian27:
With these DIP switches, you can set some basic settings, look in the manual about this time to ...
These other Firewire port you can try,
or maybe the cable is synonymous broken (either of the Cam to DV - In, or perhaps synonymous by the output back to the PC)?
Try the ADVC synonymous times of electricity to separate (ie pull the Firewire cable, external power or the power connector).
Then wiring times until everything correctly, (ie the front Cam anstöpseln, Firewire to PC) and then switch back to electricity.
If it does not go would be an idea that you have the times s.nem other computer ausprobierst whether there is vielleihct.
Then we can at least rule out that s.ADVC what is broken.
I myself am not quite sure
but I think I've had inquired at Canopus and have something to say that the introduction of the DV signal may not be with any editing software will work ...
That reminds me what a:
You could time the free tool "Canopus DVCapture" try.
I believe so go for me synonymous with the capture and the same time spend on the TV ...
(Did I tell you here and attached)
Many greetings
Christian :-)
Antwort von Blackeagle123:
Hey,
was synonymous with Canopus times just phoned. The nice Mr. s.Telefon said that it is s.OHCI Host: Because on the protocol, even when the signal through (through) seemingly 2 (!) Erknant slave devices. Pretty stupid!
He said that a solution would be to a firewire card with chipset try other things. Because a new firmware or drivers available for my card. The fact that Canopus is broken, he thinks not. Normally it would be so that the camera detected either in full or not at all recognized. But the error that the PC just shuts off after the camera several times and recognized again was not recognized, is actually a "mistake" with the Firewire card and not with the close!
I will now s.Laptop try and see if he was detected.
Until then! Thank you very much!
Many greetings,
Constantin
Antwort von Blackeagle123:
Hey,
So s.Lapotp klappts. Then it can only be the firewire card.
Your program, unfortunately I could not load ( "no authorization" or something then, even though I'm logged. Ichs Maybe try again later!) But anyway I think that the program is not much help, since it is already a problem in Windows act.
Many greetings,
Constantin
PS: If the firewire card after connecting a perfect device to the PC Absürtzen brings, it seems to not have to be good hardware. Since I now fear that my firewire card, the ADVC110 zerschießt (eg due to too much electricity s.Port). The problem I had once with an older but very good Panasonic Camera. Then after connecting s.den aufm PC mainboard DV blown out ...
And if nothing happens once, it is likely in the future synonymous nix dran happen. Hopefully ^ ^
Antwort von Blackeagle123:
Download now synonymous klappt ^ ^
Antwort von Christian27:
Hi :-)
Then you buy s.besten a simple PCI card with Firewire ports, which are certain very favorable.
Because of the power supply:
I have with me an extremely power drangemacht, because I do not ever want to have switched (ie via USB power).
If you are interested, I wrote you sometime my old posting on the subject here in the forum rausgesucht:
http://forum.slashcam.de/firewire-switch-bzw-an-aus-schalter-vt61424.html?highlight=advc110
Many greetings
Christian :-)
Antwort von Blackeagle123:
Thank you! =)
Hast thou then the Firewire power turned off, or on the mini-Firewire (4pol) connected?
Anyway I'm just s.Schnitt PC, when I cut, I find, therefore, of the really rather handy when he s.geht.
I have a cheap PCI Firewire card in the system. But I think that was exactly my fault. Now, I rather have a few euros more to spend and to know what chip is installed! :)
Thank you for your trouble! Is really something special ...
Many greetings,
Constantin
Antwort von Christian27:
Hi Constantin,
I have over the 6-pin connector with the PC.
And then I have in between a 6 - to 4-pin inserted, thus eliminating the current inflow.
Many greetings
Christian :-)
