Frage von BRNovize:
Hello PRO. It is a problem in the Recording with the ADVC 110th
I suppose that I have everything set correctly and connected since I About the ADVC 110 (DIP switch 6 on, or OFF, Analog In [blue light goes on, rear cable supplied DV - Out)
on my PC (Win7)
Video 8 tape with the
Sony CCD-TRV27E, Handycam Vision "
in the capture window "Studio import" my program
Pinnacle Studio Ultimate 14
can be "unlimited" look.
I press start, but on recording, the program sometimes takes 2 seconds to 2 minutes - then stop - although I noticed that as of Canopus magic of analog to digital (blue control) modes.
Turn to a manual back, the screen stays black - the Handycam but runs next.
In the archives I have found no evidence.
Good advice is expensive!
If the setting of DIP switch Pinnacle wrong or need to be adjusted (try the program in turn influence Canopus?). I'm just an amateur.
Thanks
BRNovize
Antwort von nicecam:
Hi, I have the ADVC300: from handling her should not be a big difference.
I guess the 110s has on the back synonymous DIP switch row left (mode selector switch 1) and right (Mode Selector Switch 2)
I suppose that I have everything set correctly and connected since I About the ADVC 110 (DIP switch 6 on, otherwise OFF ... I assume you mean the left turn. If
only switch 6 is ON (PAL video format) is available, it surprises me that you have a signal on the PC at all, because also switch 8 (operation mode) must be "PC" Also on "stand".
The rest (the switching of the blue light of Analog to Digital) I observed often synonymous: - the circuit must, of course. If then with the digitization process which did not work immediately, then I have, if I remember correctly, the equipment off and then back on.
Have the unit is currently not connected. I will check tomorrow again.
Pinnacle I know not from personal experience, I use MAGIX. Capture has always worked. As I said, was the thing with the switching of the lamp I see synonymous.
So tomorrow I'll look out with.
Will we manage already ;-)
Antwort von BRNovize:
Hi John,
ADVC110 has only one row of switches with 6 switches.
1: Digital Reference in Sync: Sync or Stream Fixed
2: Turning the input mode: Analog or Digital
3: audio mode: 48kHz16Bit or 32kHz12Bit
4: Locked audio mode: Locked or Unlocked
5: PAL / SECAM and NTSC Setup Level
6: Video format: NTSC or PAL
Greetings
BRNovize
Antwort von Alf_300:
The Dipswitch only 6 = On is already OK.
Zumindrest if analog IN and Out FW is it that goes on there should no problems.
Possible source of error could be USDI power (via FW).
Wackelkontact because of damaged FW_Kabel ..... Interface ect.
Antwort von nicecam:
Hmhmm looks, yes a bit different than the 300s.
No 3/4/6 are with me just as described. Have you no manual on this?
But tomorrow I will look again.
Oh, Alf is synonymous there. Yes but if the cable had a fault, it is likely not a continuous ("unlimited") to see picture on the PC?
Antwort von Alf_300:
Let's assume that the device is purchased and not needed in Eay is fine.
The cable is natütlich only one way, another example would be out of massive drop-outs that can write hard drive is not fast enough, wel defragmetiert too strong or too small GSAR USB. Sometimes with a different program or test only with the display of the Explorer.
In general, however, would have a Ding-Dong come when the AVC loses the connection to the PC, so you have to front synonymous times a different device (zBDVDrecorder with analog out) test
