Frage von dieoma:
Hello,
I call for short a DV Raptor Raptor Bay with my own. After some way I can and her premiere on synonymous DV Capture and am satisfied. Now I have a Television s.den Composite out the card and had the output Picture or Picture would be looking for cut marks, etc. expected - but without success.
RaptorBay is connected (otherwise würd ja synonymous the Capture not go) and the synonymous Television is set correctly. Is there a configfile, etc.? How do I if I Picture of the S-VHS Hosiden output or the composite Aufgang want? Someone used the card with the premiere and works with the analog output?
Thank you in advance for quick help :-)
Markus
Antwort von Gast alias Lumpi:
premiere what version you have? dv raptor to my knowledge is only up 6.5 supports ...
Antwort von msteini3:
If I remember correctly, the Raptor has no analog video out, but only one in. The video is used to preview s.PC monitor as overlay to get. To do this you need a free camcorder connected via firewire verbindeen him to make recording and Videoout the camcorder with the Raptor Videoin connect.
If you prefer a hast Vorscha s.TV, connect the camcorder with the TV!
Antwort von JMitch:
I use Premiere Pro 1.5 in German and when I plug-in had hineinkopiert I could easily be synonymous to the digitizer to use and therefore the hope of synonymous analog output goes ...
@ msteini3: The DV Raptor has an analog (composite and Hosiden) A and the output speiziell for the preview is done.
It is not synonymous to the Picture during digitiser but during the editing. For example, then the Picture what you otherwise in the "virtual monitor" seest synonymous in physical monitor - which is a frame accurate cutting and preview before burning really makes sense.
Antwort von msteini3:
OK, but that connected, a camcorder must be true, right?
Antwort von JMitch:
nö The path is: camcorder video via firewire as avi Canopus on the digitizer, and abstöpseln cut in Premiere. To cut the edges to precisely determine and later a "final inspection" on a real television to have the preview on television or on SHVS Composite.
And so we all obediently s.Calculator front lines, there is the Raptor Bay (5 1 / 4''mounting frame) ...
Antwort von Gast alias Lumpi:
So like I said, I do not think that works in Premiere Pro. I may be synonymous on the Canopus site no plug-in for Premiere Pro can be found, just a plug-in for premiere 6.0/6.5!
myself the dv raptor. but only works in premiere 6.5.
Antwort von gast aka dieoma:
ok - if you are under Premiere 6.5 uses - because what you need to configure? Where do I whether composite or s-video out? Or eh always comes from the two outputs the signal?
Antwort von lumpi:
is a long time ago that I have the dv-raptor times used ... but had no problems. under project settings, you can click where the premiere preview issue is ... with the new powerful pc can I find the dv raptor somewhat superfluous ...
Antwort von Stefan:
Hello,
I call for short a DV Raptor Raptor Bay with my own. After some way I can and her premiere on synonymous DV Capture and am satisfied. Now I have a Television s.den Composite out the card and had the output Picture or Picture would be looking for cut marks, etc. expected - but without success.
RaptorBay is connected (otherwise würd ja synonymous the Capture not go) and the synonymous Television is set correctly. Is there a configfile, etc.? How do I if I Picture of the S-VHS Hosiden output or the composite Aufgang want? Someone used the card with the premiere and works with the analog output?
Thank you in advance for quick help :-)
Markus IR signal from your camcorder to AP with DV-IN (DV device, see below) of output and from there via S-video or CVBS to TV directly or indirectly, with a detour via S-Video -IN/S- video - Out of the DV Raptor.
http://www.ericvandenberg.nl/setups.html
A digital-analog conversion in the DV Raptor is not planned.
Good luck
The thick Stefan
