Frage von Drive:
Hi all, \u003cbr /\u003e\u003cbr /\u003e land for small filmmakers have I risen recently, the GH-2. Reasons for this system were \u003cbr /\u003e - "Smaller" sensor that facilitates the difficult Schaerfeziehen \u003cbr /\u003e Opportunity to turn-in 1:1 mode with higher noech Schaerfentiefe \u003cbr /\u003e Short-contact measurement well for adapting other lenses \u003cbr /\u003e Good-quality image, at least in the top group the filming Native Instruments \u003cbr /\u003e Compact \u003cbr /\u003e -Affordable \u003cbr /\u003e Swivel display well on film \u003cbr /\u003e ... \u003cbr /\u003e\u003cbr /\u003e Predicted to be negative and were accepted: \u003cbr /\u003e Limited Choice of manual-wide angle lenses \u003cbr /\u003e Photo-quality moderately \u003cbr /\u003e Canon for film makers spread a little more, more accessories support, etc. \u003cbr /\u003e Panasonic builds traditionally-engined labbe Plastikgehaeuse \u003cbr /\u003e\u003cbr /\u003e The Plus Minus hit list then synonymous thus. Sofar so good. Some score but I was surprised but then: \u003cbr /\u003e\u003cbr /\u003e Image quality at ISO 160 and do NOT completely free from noise \u003cbr /\u003e Ok, not catastrophic synonymous and above ISO 160 still usable. Based on the effusive reports on the net but since I had expected more. But what the hell, still ok, more for the price is not. \u003cbr /\u003e\u003cbr /\u003e Banding as a visible problem. Ok, so the wist well at 8-bit and 4:2:0. What the hell, send itself. \u003cbr /\u003e\u003cbr /\u003e Strange side effects-the shutteradjustments. Such extreme interference on mains-powered light sources were new to me. The shutter speed should be carefully begracht moeglichts a flicker adjustment, otherwise the same strip of an old video tape. Practically this means that the shutter swings mostly between 25 and 50, which in any case theNormally cinematic equivalent and thus again is fine. \u003cbr /\u003e\u003cbr /\u003e \u003cspan style=\/> \u003cbr /\u003e -As THE bad design all over, I turned off the camera standing by thread. Practically, this means that the camera only aufwitzt a.diesem thread. The rest can be easily moved into the rubber underlay the camera plate. Here I hope the problem can still be reduced by 50% by I adjust the camera plate corresponding to a whopping edition to get. How do you do it? \u003cbr /\u003e\u003cbr /\u003e -M4/3-Lens Mount allows tilting movement. Sad but true, that if you ever loaded a little sideways Objectively, it is no longer continuous. Remedy? Perhaps the Objectively additionally with a pinch clamp back on the tripod plate? has anyone experience with something. In addition, the Mount can bend in Kameragehaeuse. \u003cbr /\u003e\u003cbr /\u003e Objectively, the game has. This point seems to me the
 |
Antwort von Filmo:
Sell \u200b\u200bthis unstable Plastikschrottgehaeuse model would give me, you can no longer lives in the :-)) banding, Rush paired thread at 160 iso, jiggling Lenses, Tripod prominent, with regular photo quality that is much more than the police allowed- So it comes wenns-I'd take it. \u003cbr /\u003e\u003cbr /\u003e Perhaps, however, synonymous only the currently prevailing cold weather to blame for your (high) FF is frozen and therefore schwergaengig. \u003cbr /\u003e\u003cbr /\u003e In the seriously: if you have to find the net do not, then should the others have not noticed, too many will not be the a.dem small marvel using NEN FF and if so, by the Indians, the hat so much game, that's all you have no preference other synonymous :-)
Antwort von Drive:
Somehow I have the feeling that you do with your meaningless post-blah about me want to make fun of. \u003cbr /\u003e\u003cbr /\u003e Or did I read about your answer?
Antwort von Frank B.:
Filmo trying to say that he does not have your problems ;).
Antwort von Bernd E.:
\u003cdiv class=\
Antwort von Drive:
\u003cdiv class=\"Bend it" does not belong to a lot (including all course mm but visible) \u003cbr /\u003e\u003cbr /\u003e\u003cdiv class=\
Antwort von Filmo:
make me of no one funny ... and yes, between the lines you'd see quite a lot can :-) \u003cbr /\u003e\u003cbr /\u003e Enclosures for one in this price segment is ThyssenKrupp Steel only play a small role and their own motor skills may well be aimed synonymous with other manufacturers, if you zBCanonerwaehnst is not all play their own experience! \u003cbr /\u003e\u003cbr /\u003e With a suitable tripod plate (without rubber-edition!) You will be able resolve the problem tripod thread protruding slightly, because most have a bigger hole that would swallow this slightly above millimeters. \u003cbr /\u003e Otherwise, I agree with Bernd, what do you use FF, perhaps a still synonymous your constellation would be helpful.
Antwort von chackl:
He wrote it before know that he used a Tilta FF. \u003cbr /\u003e\u003cbr /\u003e guggst you here. \u003cbr /\u003e\u003cbr /\u003e http://www.prophotographygear.com/images/FOLLOW 20FOCUS/HDSLR%%% 20KIT 20TILTA_8.jpg
Antwort von Filmo:
yes, I only saw after I had already typed in answers :-)) \u003cbr /\u003e\u003cbr /\u003e And with the figure I thought its special structure, including the camera. \u003cbr /\u003e\u003cbr /\u003e Have looked at other pictures of this FF synonymous, so the rubber pad A.The camera mount would be even a possible cause, especially if the focus ring of your lens, perhaps (because of cold weather) should be something schwergaengiger. \u003cbr /\u003e But the exact structure we are familiar with (yet).
Antwort von chackl:
AHSO :)
Antwort von wenzel chris:
\u003cdiv class=\
Antwort von Natalie:
your first meaningful contribution ;-)
Antwort von chackl:
Then, just the way :) \u003cbr /\u003e\u003cbr /\u003e http://bit.ly/yOig72
