Frage von Michael.Fischer:
Hello.
Search again for several hours after the solution to a problem with which I Rumschlag me for over a year.
I work USALS media and performance artist and therefore is very embarrassing situation for me.
My now 30 tapes waiting for the revision.
Unfortunately, detection of both yet ScenalyzerLive Premiere Pro the camcorder and can I control this synonymous with the interface.
Only with the Pictureübertratung it does not work.
Facts:
1st Canon HV20 has an older Firewire cable contact with the computer
2.Control device works. Thanks diesesm forum! (THANKS!)
3.Trotz much trial and error, no progress and no picture transfer.
My approach is that it gives a problem with the graphic representation. No Picture => logical (?)
Have therefore already installed DirectX.
Furthermore, with the whole HDVSplit tried (Gar no signal)
Also helped me Gspot not synonymous next (as synonymous?)
The cable? A year ago it was still works on other computers.
There are many topics on the Internet worldwide hierrüber but even in this forum, I found none that has about the same problem statement.
I hope for solutions and am a little perplexed,
but would not give up yet.
Best wishes and peace With you (not a war without technology)
Michael
Antwort von srone:
which operating system, which firewire controller?
First connect s.computer camera, camera on, boot up computer.
if win7, firewire controller drivers "down" data (legacy old).
lg
SRone
Antwort von Michael.Fischer:
Hey SRone
Thanks for the fixed answer.
OS: WinXP Sp3
Firewire controller onboard
IEEE 1394 Bus host controller
- OHCI Compliant IEEE 1394 Host Controller
- VIA OHCI Compliant IEEE 1394 Host Controller
There is also a PCI firewire card with 2 ports
which is listed under Network Adapters.
Same problem here.
The video capture device is Legacy?
Is it possible to correct something here?
The Canon HV20 is recognized on the workplace as a digital camera, I can access it synonymous, but when I press on Picture Studio, the process is interrupted
regards
Antwort von srone:
avoid the via controller.
in premiere pro hdv there are no visual, but is still captured, already tried?
hdvsplit works in the stands with a regular image, your cam to vcr?
lg
SRone
Antwort von Michael.Fischer:
How or How do I replace the Via controller well if?
So Premiere Draws on and running the canyon. But once I stop I get the result that 0 frames was recorded.
Sure, the cam is on VCR, so if you think the play mode.
Otherwise, I beg your indulgence.
Camcorder is not recognized or connected
shows HDV Split to 0.7.
regards
Michael
Antwort von srone:
According to your above post you have 3 firewire ports, use the other, not via the example, the plug of the card,
do you have the connection sequence of my previous posts tried?
lg
SRone
ps: under xp ran s.besten the texas instruments controller.
Antwort von Michael.Fischer:
Hey.
If you mean connecting your camcorder, turning & Computer Start.
Yes several times already. Unfortunately, no positive result.
The Texas Drivers I will still raise and then sleep
before I see the problem again completely wears.
Is unfortunately just a shame, because at the moment, as synonymous tomorrow
a video project with primary school children and adolescents is due to me and the lack Überbearbeitungsmöglichkeiten let me once again have something embarrassing there.
Thanks first to the extent SRone.
Whether the Firewire ports to the adapter card with the onboard port fight, I know of no direct as I can verify this.
Get as soon as I have the Texas Instruments driver,
disable the adapter card but first a test basis.
Good night.
Michael
Antwort von srone:
you misunderstand something, it is not about the texas drivers but the hardware controller chip, which brings texas drivers installed for the via chip does nothing but crash might disable the onboard (via) firewire controller in the device manager and use you for trying the external card. you might even here a driver update hilt, but only with the appropriate drivers.
lg
SRone
