Frage von CHR-Film:
Hello.
Weis not whether I'm right here ...
My problem!
Did the LANC control Sonyvor of me! Unfortunately, the cable jack which zum 2,5 times what goes into the camera belongs to.
Can I and how can I use these cables to solder back together?
Already have a new 2.5 naturally what Jack has 3 cable.
The LANC cable (the first cable bundle) once white and a cable is not isolated!
The LANC cable (the second cable bundle) 2 non-insulated cable.
Four cable s.eine TRS anzulöten is difficult if you do not know what and where to be!
ADDENDUM:
The problem is not solved yet but I was 20 euros for a new arm now! (Arm + Controller) I love the Internet. :)
Antwort von Markus:
Can I and how can I use these cables to solder back together? Yes, you can plan a LANC cable to solder back together.
The easiest would be the assignment, if the opposite of shows where the individual wires should be kept. Then there would be no problem, everything on a new jack to transfer.
If the cable directly s.den joints of the connector should be demolished, traces would be announced. Cable length, Rißstelle ... a little play CSI. ;-)
Antwort von CHR-Film:
Yes danke schon mal.
I've tried with CSI! lol
But did not quite.
That is exactly the place where HAMA has saved and therefore s.Kabel times.
Have I ever as the new Tripod Hama GAMMA80 had the same error because of the need to replace everything.
1.Kabel is really thin and the times around it melted.
I try again to explain.
The first one includes a white streak isolated and a non-insulated cable.
When I noticed that the white on top and one is not isolated to the other end where audio is the mass.
Now one might think that the other two cables connected to the center should be but unfortunately is not so.
Because when you connect the handling has not responded.
Still other times at the core of the cable.
The consists of two non-adjacent and insulated cables which are in the middle again so have a comic Fuselschicht looks like very thin fiberglass do not want to isolate or so. I've always asked what it is.
zum Bild When the call has said to me that it's not so easy is the four cable jack s.den 2.5 times anzulöten.
Did the housing synonymous already open but the board had said nothing to me. (Solder joints)
I'm glad the first time so was able to order a part.
So look out.
zum Bild
Antwort von Meggs:
Hier
[/url]
Antwort von CHR-Film:
Yes I had the still thank you!
And strangely was synonymous with the occupancy nothing!
Habs getestet! Mux says no.
So:
BUND_EINS________________
Cable white ..................... Top
Cable blank ..................... right
_________________________ BUND_ZWEI_______________
bare wire (2 ).......... middle
_________________________ Unfortunately ...
Maybe I made a mistake!
Try it again tomorrow!
Greeting
Antwort von robbie:
The two are not isolated and the mass belong together. Now you need to help with the LANC-occupancy, in one of the links is just to find out what the mass is.
The other two cables belong to the other two poles. 50:50 that it works, if not the other way. Except you have in your present attempts already zerschossen board.
Antwort von Modellbahner:
Hello, I've meinn Remote Commander RM-95 aufgeschraubt at times to see how the times occupied. As already announced my prescribing is in the occupancy of the link Meggen correct. the original is the black wire = ground, white = Lanc (control voltage), red = Power supply. If I ask of the CHR movie correctly, his control, instead of one (Sony) whose two. In my opinion, it is not left to control aufzuschrauben and the Ansclüsse view. The two non-isolated (mass) probably belong together. try what s.die jetz s.die top or middle of the connector may come naturally to a crash (short) or the complete destruction of either the camera or the controls come. Voltage of about 5-8 volt control voltage s.die can then be used for one or the other device tötlich be. I screw with such problems is always on the device to tell me
before the assignment aunzuschauen, especially if I get a Page not know.
Gruß Bernd
Antwort von CHR-Film:
Hello folks!
Scheiss Chen's it!
LANC goes back and everything is s.der Cam IO!
Only one thing I must tell you !......
The description has an error!
http://www.boehmel.de/lanc.htm)
Da steht in dieser Reinfolge:
((= Tip LANC) (5-8V = center) (right GND)
Unfortunately this is not agreed on with the controller!
Because it was so:
(5-8V = top) (LANC = center) (right GND)
So the tension and LANC swapped.
How can something be?
Now that everything is soldered correctly funzt everything ......
Is that wrong on the page?
There can be no deviation to this is quite normal Sony product.
Ne question time yet.
I did as I said SonyCam's two synonymous and two different remotes to do so. Of course, almost all functions of the two operations with two Cam's. Only I noticed that both remotes 2 functions, the more each other does not. One can code the data show that the other may be in store's menu. The question is whether I have a remote control can adjust itself so as I need them synonymous! Have I explained that this LANC is nothing else than the control with remote control only over the data cables. I would very much like the handling so adjust the function of the focus "in which I have LANC" via remote control is possible! From Verwacklungstechnischen reasons.
That would be a really great thing.
I hope you have understood what I mean and perhaps habta an idea.
Greetings ...
Antwort von Modellbahner:
What now? Was it right.
Bernd
Antwort von CHR-Film:
Yes've made a mistake when creating the post!
Habs changed.
Again.
It looks like this.
On the Page is pure in this sequence:
(LANC = top) (5-8V = center) (right GND)
Unfortunately this does not agree with my control!
Because it is so:
(5-8V = top) (LANC = center) (right GND)
So V and LANC do not match they are swapped.
But have searched and still have next synonymous descriptions of other LANC found because it's just as described!
Why when my control is not so now is the issue because it is already a grave mistake if it angelödet is (was).
Antwort von Modellbahner:
But it is not the original Sony occupancy. Next I have described above as in a Sony original part looks like, since the manufacturer has control of your re-invented something new.
(LANC = top) (5-8V = center) (GND or federal laws of the plug)
So the Lanc is s.der top, the tension in the middle and the mass s.dicken end (where the spout is aufgeschraubt). Whether right or left depends s.wie one considers the times.
Gruß Bernd
Antwort von CHR-Film:
Yes is funny.
The tripod and the control is of Hama and the board because of the handling of it is of SONY.
But I am so glad of what the da's durchgeknallt is not in the cameras.
But why is this control with my cameras that?
Antwort von Markus:
But why is this control with my cameras that?
What do you mean by that? Was not a priori be thought of?
Antwort von CHR-Film:
It's easy!
One can only be right.
To ensure that all operations LANC synonymous with LANC Camera s.jeder function can be only one correct version, as the cable S.2, 5 TRS Male position.
However, if the electrical man says to me that after the plan ", as he of me, some of the Page had" unfortunately, after the solder on the Camera / Handling is not responding, can s.einer something wrong place.
He has the board out and put it out to compatriots to get what now where cable must be really out.
As he noted, that in default to the Page LANC and electricity had to be swapped, because when he was exchanged and again anlötete handling worked perfectly.
So there is the possibility that the requirement is not true.
If it is true but it did not seem to understand why the controls in the camera work but where in fact the LANC standard (according to the specification of the Page) can not be met.
Therefore the question how can the camera, making clear when it will actually LANC and power supply should be swapped.
One can only!
There is just a standard LANC?
