Frage von bfilzek:
Hello,
've got synonymous mal ne question because I have recently bought this camcorder on ebay. I can see and record everything, but hear no sound. Since I have no instructions for this: there is something in there, how / where you can turn off the sound?
Maybe the camera is synonymous broken?
Thanks for ne response.
Antwort von bfilzek:
Hello,
've got synonymous mal ne question, since I (recently this camcorder so) I bought on ebay. I can see and record everything, but hear no sound. Already recorded tapes, which have einenTon (!) Made not a whimper of himself. Also, the Micro does not seem to work.
Since I have no instructions for this: there is something in there, how / where you can turn off the sound?
Maybe the camera is synonymous broken?
Thanks for an answer.
_________________
Greeting Benno
Antwort von stuckywerner:
Hi Benno,
if you do tape on the camcorder anschaust:
you have headphones plugged in when PHONES?
Gruß, Ellen
Antwort von DjDino (Toth Dominik):
May well be that this very old (because Video8) Camera is gone, most likely due to aging of capacitors, too long storage, and thereby often synonymous accelerated damage due to commissioning.
Details see here:
Used Broadcast Cameras on eBay Better reason never to buy a camcorder that is older than ~ 10 years, and certainly not of Sony.
Antwort von Maxim:
yes, both have as synonymous with Headphones s.TV checked directly, with no success ....
Antwort von Markus:
Hello,
perhaps you take time contact with the seller, and pronounces the behavior of your "new" camcorder. Possibly the defect was known before?
Check in advance nor the eBay listing, ie, reread the text very carefully (you've probably done it before bidding / buy, just like the one). The defect should have been called, you had bad luck.
Otherwise you could be the seller's decision to withdraw the camcorder kulanterweise easier with the announcement of a negative evaluation. - Thou hast made hopefully no rating?
Antwort von multimat:
, thank you Mark,
I think I'm falling into the trap that has been described DjDino (): s.Anfang the unit has played all the sounds, ie, after investigating everything is working, and therefore I have left a positive synonymous ...
such is life ....
Thanks anyway
Benno
Antwort von Fuffzehn:
I dig out this old post again, because I had the same problems synonymous.
The thing is, I have some idea of electronics, I wanted to open the camcorder easy times and replace ggf components.
Unfortunately, I have succeeded not because of the old bolts.
Are there any good trick, rauszubekommen the screws (if possible without ruining it, I've already done in a).
Or you think I would rather have a bit of money to invest in a new camcorder?
Greeting
Nicholas
Antwort von Markus:
Are there any good trick, rauszubekommen the screws (if possible without ruining it, I've already done in a). Hello Nicholas,
If the screws are already corroded, then it only helps aufbohren yet. However, it is true that there are corroded screws for a poor storage, which could be an indication of other problems inside the camcorder.
Or perhaps you have not used optimally suitable screwdriver one? Which of the watchmaker's very good because the have a perfect fit.
Or you think I would rather have a bit of money to invest in a new camcorder? That I can not judge the distance, but not so much you can destroy more than when Plan B already are preparing for a new camcorder.
Antwort von Fuffzehn:
So rausbekommen I had 3 screws, Dannacher did not go to the next.
In the boring of the problem would that I would get shut Dannacher camcorder synonymous again.
And with what kind of drills can be boring of sowas?
Greeting
Nico
Antwort von Markus:
In the boring of the problem would that I would get shut Dannacher camcorder synonymous again. With the three screws unscrewed as a model perhaps you can muster something appropriate. But that will indeed only be an issue when the camcorder is working properly.
And with what kind of drills can be boring of sowas? A Dremel with a small metal drill would be optimal. This tool is not as hard and you can run it well. First you have to pay off so only the cap of the screw to loosen the connection. Everything else requires a lot of sensitivity to the surrounding plastic, which will hold the screw is not damaged.
Maybe you can share with a very fine metal drill a small hole in the center of the screw and unscrew them with a toothpick or a metal tip? Thus, in the way I would try this first, because usually in such a corroded screw the tops.
Antwort von Fuffzehn:
So I Dremel and carbide drills, because I make s.and s.synonymous boards, which should therefore not be the problem.
However, I believe that the fine drill as quickly break off and jam.
I'll try it but at least once.
/ edit:
Habs get open, even had to boring of a single screw.
With the replacement of the electrolytic capacitors have been angfangen, but that could still take as synonymous.
Have now another problem, I disassembled the Optics times to get rid of the IR filter in front of the CCD.
Has worked out perfectly synonymous, but apparently the auto focus has some small problems, the spins and turns, only the picture is not sharp. But if I zoom in I can to focus it.
What could be the reason?
Antwort von Fuffzehn:
Will you not answer me?
