Frage von Jürgen_He:
Jürgen Kanuft wrote:
> Hi folks,
>
> I'm looking for a simple tool Amcap similar with the one I use the Picture
> Video Camera on the screen can show.
>
The MPC
http://sourceforge.net/project/showfiles.php?group_id‚303&package_id„486)
can do that (menu File> Open Device)
Gruß, Jürgen
Antwort von Jürgen_Kanuft:
Hello Jürgen
>>
>> I'm looking for a simple tool Amcap similar with the one I use the Picture
>> Video Camera on the screen can show.
>>
>
> The MPC
> http://sourceforge.net/project/showfiles.php?group_id‚303&package_id„486)
> Can do that (menu File> Open Device)
thanks for the tip.
While working with my Firewire-Cam,
but not with my Composite Cam.
perhaps there is another program that I could try?
Gruss
Jürgen
Antwort von Heiko Nocon:
Jürgen Kanuft wrote:
> actually works with my Firewire-Cam,
> but not with my Composite Cam.
Then you have something wrong.
What hast thou in the menu "File" -> "open device" selected?
How exactly expresses the "not working"?
Antwort von Jürgen_Kanuft:
Hello Heiko
>
>> Actually works with my Firewire-Cam,
>> But not with my Composite Cam.
>
> Then you have something wrong.
>
> What exactly did you do in the menu "File" -> "open device" selected?
Studio PCTV USB / Radio (PAL)
> How exactly expresses the "not working"?
No Picture!
Gruss
Jürgen
Antwort von Heiko Nocon:
Jürgen Kanuft wrote:
> Studio PCTV USB / Radio (PAL)
Aha. So as Pinnacleschrott capture hardware. Well, who does not anger
, which is what makes ...
>> How exactly expresses the "not working"?
>
> no Picture!
Correct source?
The MPC are you using the menu "Play" - "filter" to the individual
Components used to play DirectShow filter network.
If the driver was good (of which I have not, however, Pinnacle
would necessarily expect), then one of the above sub-menu
displayed filter anything with "crossbar" in their name and
Clicking on a configuration dialog in which you have the correct source
can choose. What that is depends, of course, exactly like you
your camera to the Pinnacle portion connected searched.
There are still a lot of synonymous further opportunities for
(Fehl-) configurations. You'll find them for half of the dialogues
Filters called in each menu, the other half in the
Capture settings of the MPC (Menu "View" -> "Capture").
If you are with all of these controls did not succeed,
then I have bad news for you: Your Capture Hardware
is scrap. But did you pursuant to the above, certainly
already guessed ...
And yet another, even worse, I have news for you: You will
the case then synonymous with any other generic Capture program to
Running. There is no more control than you
with the MPC can achieve. All other capture programs
best if the same ways, but usually much less.
What remains then you are just three options:
1) The schrottigen Pinnacle hardware is just as schrottige
Pinnacle software.
2) Reasonable hardware purchase.
3) The thing here.
Antwort von Jürgen_Kanuft:
Hello Heiko
>> No Picture!
>
> Correct source?
>
> In the MPC are you using the menu "Play" - "filter" to the individual
> Components of the play used DirectShow filters network.
thanks for the tip.
Experimenting with the playback filters, the setting for the
Choice of video input as a signal source unearthed;
now it works.
Gruss
Jürgen
Antwort von Jürgen_Kanuft:
Hello Heiko
>
>>> No Picture!
>>
>> Correct source?
>>
>> In the MPC are you using the menu "Play" - "filter" to the individual
>> Component used for playback of DirectShow filters network.
>
> Thanks for the tip.
>
> Experimenting with the playback filters, the setting for the
> Choice of video input as a signal source unearthed;
>
> Now it works.
>
... but not yet as I was looking for:
after the restart of the MPC, I do not immediately get the picture of
Camera shows only cumbersome but must select the device.
There is a setting the Picture without additional input
after the program start to see?
Gruss
Jürgen
Antwort von Heiko Nocon:
Jürgen Kanuft wrote:
> ... but not yet as I was looking for:
>
> after the restart of the MPC, I do not immediately get the picture of
> Camera shown but must first select the device cumbersome.
This is bad, I did, however, of Pinnacle synonymous little
otherwise expected.
> There is a setting the Picture without additional input
> after the program start to see?
No.. Actually, this should be a proper filter in the manual
Filter configuration made persistent, ie after a
Restart the program should be the last source of synonymous again
active.
If you are with normal user rights work, then it might be
might help the matter again with admin rights, go through.
If it works so, chances are good that it synonymous with
Account Admin as the last chosen setting is active.
If it is, however, with the admin account works as desired,
but with the user account is still the old setting
is, you could be as a last attempt to the user account temporarily
Admin rights to the desired setting and then the
User Account Admin rights to withdraw again.
It all works or not is of a priori not applicable, because you
sowieso worked with admin rights then you have finally
lost, at least as far as the capabilities of the MPC is concerned.
Then you could be only with an additional automation solution
(eg Macro Recorder) Rumgeklicke least the stupid car
it can be.
