Frage von DoBBy:
I think I'm better times on a separate thread, even if others should have the same problems:
The following problem has emerged: it is about my external micro Rode NT3:
I do not know whether this should sound the way it sounds to me, is certainly with me the whole sound, no preference where I connect noisy total. My voice I hear is very dim and almost none of this are handling noise s.Mikrokörper or cable very very loud. This is both s.Camcorders as if synonymous s.PC connected.
If I cry in, comes the voice of something better, but is a very loud noise heard. So I would then remain but rather the internal micro-camera with a decent fan in the background. And at a micro for 150 ¬??
The Micro was connected with a Beyer Dynamic XLR to jack cable s.die devices. (~ 16 ¬ at Thomann)
If the s.Micro now, or there is something broken? I noticed synonymous, do not know even whether that is to be such that the rear s.Micro out one of these next three XLR bars, rises as the other second If I touch but everything is solid. I can not as synonymous finished push or something.
So here in the video as clear as it sounds far from it. As I said, it remains totally noisy and noise control are extremely audible! What is going on here?
I hope times fervently that it is not the Micro itself. Perhaps the connection? But what can that be?!
The Battery (Duracell) today re-purchased in discount stores and used.
Would really happy about help! : (
Antwort von rush:
g'd evening,
the problem will probably be a combination of battery and adaptation to handle. The tension and the level will eventually be too small tear to s.deinem camcorder or PC with Jack was ...
Test the Camera with Microphone times s.einer XLR input or a mixer, the 48P is available .. because it should work fine and provide enough level.
Achso and that of a contact is longer quite right ... The pin makes the ground contact and has virtually the first priority and is therefore always remove the first and the last as securely
Antwort von DoBBy:
Good evening
First of all thanks for your help!
If I understand correctly this means for me:
If my camcorder (SD 707) only one phone jack input and XLR has NO input, I can forget this Micro? For this is the case. I have a mixer, at least privately here not there.
Funny that I was the Rode NT3 as camcorder Micro has recommended here ... Is there a way or can I just forget the micro without XLR connector?
A friend of me has, however, a synonymous XLR-Micro s.seinem camcorder (is a stereo microphone and has a synonymous XLR to TRS adapter cable.) Because it works properly ...
Antwort von rush:
Well in theory, should the microphone already synonymous with the 9V can provide a reasonably aktzepatblen level - but probably is the Eingangspreamp your little Panasonic not simply designed and therefore there is a problem.
For dynamic XLR mics around this problem is not as strong as they can come only by the volume level to oscillate and do not need a separate voltage. This you can probably synonymous easily adapted to handle and connect. But dynamic microphones have just again very different properties.
Whether NT3 now necessarily a typical camera microphone is I do not know ... From her size, it's at quite compact ... that should be okay.
For the case that it does not have a defect, it simply trying times for someone to test the device with a P48 Power has and can connect it directly via XLR ...
Antwort von hubse:
Hi Dobby,
after I've recommended it to you I now feel a little responsible synonymous if you have issues ...
I use NT3 with the SD707, and it is no (or almost no available) Noise, voice I hear as perfect with NTG2 and Co. (I told you I believe in what was then synonymous thread written). So there should be no problem from Eingangspreamp the SD707 (it's because she is gone, but you would have had the problem synonymous with other mics).
Would it be true that microphones with XLR jack are not usable in principle that would apply synonymous for Beyerdynamic MCE 72, Rode NTG2 etc., for they have finally synonymous an XLR output (and battery power)!
NT3 is synonymous made for manual operation (at the bottom are a few links to it), so if there are handling noise, then there is an error that is not natural and therefore not due to a bad buy is.
Derived NT3 is like to lose weight, etc. of choirs. These sound sources are usually aware of Micro removed as a speaker in front of the camera. Thus, if the speaker is not heard in front of the camera, that's not normal for this Micro!
So breathe deeply, do not go mad and then we try to find the error.
I have no problems with the XLR - on mini jack cable. Which cable you use exactly? (Below is a link, there is the cable that I use it). Nachdems a mono-Micro is, is like selling a mono-cable after the SD 707 has a stereo input could be the fault (comparatively later times your jack with the link below),
With a field recorder / camcorder and professional XLR only to hear the sound of course again (a bit) better at. If the cable is longer, then you can really only work with XLR (and then I use the always synonymous field recorder with phantom power).
I do not know how to listen your Noise (lad perhaps a sound sample on YouTube high, yes it can then delete synonymous again), nachdems me at work, the error must lie somewhere else.
Maybe It lies wirlich s.Kabel ONLY. The non-XLR cable, problems with "radiations" (power, phone, etc.) because they act like an antenna ... the longer the antenna, the worse. That's what happened then but just as with NTG2, MCE72 and Co.
You could try it once with NEM XLR cable. Then you still need an adapter of XLR to TRS (an adapter cable is no where in between, for example, something like: http://www.thomann.de/de/planet_waves_adapter_klinke_xlr_pw_p047aa.htm) and of jack to mini-jack (of XLR to mini-jack there seems to be no direct). Then the problem would be fixed antenna schonmal. If there two rausschaun adapter from the camera, looks a little out of stupid - but if the noise is gone then ...
It lies perhaps synonymous s.der connection, but I'm assuming that you want your cable several times down and back on it did.
Have you ever tried to play around with the level settings (always "possible level setting" high, so you have to step up behind not so much - because that leads to Noise).
Also because of you "handling noise," talking about, really s.Micro arise or be incurred only when you touch the cable? My NT3 is actually quite sensitive to the touch and it should be synonymous to the description ..., see below left. Cable, however, are very sensitive to the touch (only XLR cables are "insensitive"), this is a problem at all without microphones XLR cable.
Your question of why one of the time looking out s.Micro next is explained in one of the links, I do not know just what ...
Les you the time by (synonymous if there were some posts a little bit lasts until they come to talk again NT3, well worth the read), the contributions are likely to interest you in your situation.
Under the link which is to cables and for dowries.
http://www.filmerforum.de/Forum2/viewtopic.php?t=2454
From this link (have to go down a bit) is synonymous to what the mechanical stress of NT3 - "if a drummer instead of the drums once the micro" applies -
