Frage von jimi:
times have an extra thread dafuer opened. is actually an excerpt from "ton fishing with the XL1S"
I pushed on a tip, how to, for example, when the XL1S canon xlr-schlterstütze for can save 200 ¬
Experienced technicians can indeed times its mustard to give, whether it works, or a good is gone.
in the book (there will now be back Various responses) "Hollywood for bargain hunters - Digital shooting of Frank Sauerland writes in this chapter" 3 Sound "that called for cameras without xlr connection, with only 3.5 mm jack plug, cheap an adapter can be soldered.
I quote:
In the music business, they receive the necessary connector. TV technician when they buy a low-frequency cables with conductor and shield (wire mesh around the ader).
this cable must be back in the 3.5 mm jack fit.
plug in xlr xlr or the clutch (the equivalent of the plug) are now pins 1 and 3 bridges. At the Pole 2 comes ader, s.den united pin 1 is the mass soldered, so the shield of the cable.
the first edition of the book is of 2004. So right up to date, ALSO I mean, there was but in any case already xlr-jack adapter to buy, or are the garnicht? He also speaks s.anderer point of interruption vulnerability unscreened cables with unbalanced connections. then it is hardly the instructions to such a type here or not? [/ quote]
Antwort von Lothar 2:
Hello!
This adapter (stereo) are often used at Ebay for around Euro 10, - offered. I have often soldered itself (a bit Fummel work) and get ready-made synonymous purchased.
If you solder them, the parts are just as expensive as a finished part with Porto,
Gruss
Lothar
Antwort von jimi:
My question was whether an alternative to xlr-schulterstuetze is?
I have, if I use an adapter so no disturbances in the sound recording?
Antwort von mov:
depends on whether the adapter is not symmetrical or if it supports symmetry, then, he has the advantage that there is less interference by the unbalanced connection by long cables have caused. If not, then this cable is a good alternative.
Antwort von jimi:
: (I feel misunderstood. Otherwise I always get the best answer ...
Antwort von MBN:
This solder bridge is no longer symmetrical ...
Antwort von Markus:
See synonymous here:
ton fishing with canon XL1S? I suppose, Jimi examined a possibility of lead to make gold. ;-)
Antwort von jmi:
I suppose because I am not the first;)
Antwort von Blackeagle123:
Hey,
There beside the XL1 more cameras, with only one input jack did. What do you think because, as we are for smaller features in the school, etc. the sound off? We do not use the camera microphone for an interview or an external recorder (with brief shots). Either poor quality or too much effort.
Obviously this takes you to a huge short-XLR jack cable, or equal to an adapter that you plug in the Male s.der Camera can connect. (Note that nothing is lost!)
The sound is limited by the short length, in principle, just as if you have the Microphone directly via XLR cable connects. Of course one could synonymous (as in the case Studios) DIS intermediate stop, again from the current decouple ... When someone's cell phone and called anlässt is still buzzing!
Conclusion: Take such an adapter, closing him s.die Camera s.and you hang your XLR Microphone tuned there.
Requires Microphone, however, a phantom, it is complicated and you need a Battery / a Battery. Here is a camera, the phantom provides practical.
Hope you like so that I could help.
Many greetings,
Constantin
Antwort von jimi:
YES! thank you very much!
Antwort von Markus:
I suppose because I am not the first;) In fact. I have times synonymous for a simple solution - and I take a camcorder with XLR connectors purchased. ;-)
Antwort von mauriceg@gmx.de:
That I think is the best solution and total s.billigste.
VG
Jojo
Antwort von Blackeagle123:
perhaps the best, yes .. but the best?
You need me to explain!
Many greetings,
Constantin
