Frage von DjDino:
Hi folks
Problem.Mein've got a JVC camcorder (GR-DF540E) has, unfortunately, the rare filter diameter of 30.5 mm, but now I want a Sony with 30mm wide angle lens mounted on it (http://www.geizhals.at/deutschland/a56831.html)
Visually, it is compatible, fortunately, super quality with virtually no cushion, etc.-distortion ... already been tested. (turn on hold)
I changed my magic that I, perhaps with an adhesive tape which I wrap 1-2 times around the thread of the 30mm wide-angle converter it into a 30.5 mm-thread could be, or is there more tricks?
I try to slip it that is just so screwed while the converter thread too pure, so is just not screw our little girl. (Because of the stupid, the same 0.5 mm) are missing
Adapter rings for 30 to 30.5, it does not exist, never found, not even on Ebay, and I want to spend not only because such a 0.5-mm-issue 20 euro upwards for something.
Because those who know tricks?
Antwort von Peter S.:
Such an adapter can not build. The 0.5 mm difference is not sufficient to capture an internal and external thread. The next largest diameter (37mm?) Would be more suitable. Can perhaps unscrew the front ring of the lens? When pure-and unscrew the lens thread caution is called for, otherwise, a front lens is due, for the entire camcorder must be dismantled.
MFG Peter
Antwort von DjDino:
"Can you possibly unscrew the front ring of the lens?"
Unfortunately no, all of a piece, (
Thanks for the warning message with the Frontlinse.Ich to prevent the lens so that I desperately reindrehe sodas too much what it s.der Lens docks could damage these (guess that talked with you more so) - fortunately, can not happen because the 30 , 5mm threaded s.Camcorders almost twice as deep as the 30mm s.Lens.
If so angry all ... especially since it worked so well during my tests where I drangehalten I hate it into the corners a beautifully sharp and quasi-zero-weitwinkel squigly Picture.Nicht times the "Tunnenblick problem" in Minimum Zoom damit.Und now I will fail everything s.0, 5mm, (
Well, I meanwhile an interim gefunden.Habe the lens thread about 1 1/2-mal electrician with a soft insulating tape so soft umwickelt.Dieses nestles nicely into the thread grooves sbzw into which it has now been widened because apparently some 0.5 now I can almost synonymous reindrehen and it keeps screwing very gut.Ganz I can not, however, because the "tape-grooves" all the same sliding machen.Naja not exactly synonymous, but it holds.
Is just stupid if I want to take it off, at some point the tape is worn away or dissolves when it is old ... somehow not satisfactory in the long run.
Should I buy now because of the truly another wide-angle lens? Maybe we can refine the with the tape still?
Antwort von Jan:
Hello,
Perhaps the magnetic variation is not stupid.
In converters of low or Cokin Hama (eg) since most recent, there is the magnetic variation. Page One s.Converter was plastered, and the other on the camera lens.
By putting the two together, the magnet holds it in the desired position.
I have tested this converter times already and it has kept (Cokin)
Is useful if the camera has no thread and still is in front of a converter.
Maybe you'll get a converter so cheap (in the business he is 50 ¬) and do off the magnet surface, or they are tinkering something similar.
Wide angle adapters-to-stick LG
January
Antwort von DjDino:
Thanks synonymous Gov. ..
I have had it easy now but tiles with 2 components superglue bonded (nicely into the grooves), hold Bombenfest and is now synonymous dicht.Kann just absolutely never fall again:) But I will not anyway because the zoom with Auto - AF with Wide Angleauch this is quite good (up to about 12x).
Was pretty tricky, synonymous only a drop of glue on the lens and ... fortunately went well.
Antwort von Jan:
Well, there's still a hobbyist in the forum, and not just Ruessel Blackeagle123.
I is synonymous gleub better so your version.
The Hama adhesive / magnetic adapter was 27 mm in diameter, Cokin 22 and 27 mm, they would therefore have been too small anyway.
LG
January
Antwort von Markus:
I would have stuck that on Lenses on a matching to Camcorderobjektiv Ø adapter ring. Then, the camcorder had not been sighted for ever ". ;-)
