Frage von Moritzk:
Good evening, dear Slashcam,
I wish you my first DIY in the field of camera equipment imagine.
I've built myself a camera dolly trolley including rails.
What say ye to my design where I could still make improvements?
Have recently heard that we should sand in the pipes or rails fill, so they are harder and thus fixed to the ground.
Here are some photos.
Many greetings,
the Moritzk
Antwort von B.DeKid:
Gude Chef
Jo seems ok from .....
Now Part of the ideas ;-)
The wells Tripod not fall.
Perhaps it even rotating plate and with middle Zugsicherrung.
Would I connect rails / example. Flat metal strips s.schweissen.
The thing I respect the synonymous disconnect this connection can pack up.
Train or sliding fit options, so I thing can be pushed or pulled.
That should be his first.
MfG
B. DeKid
Antwort von Moritzk:
Gude Chef
Jo seems ok from .....
Now Part of the ideas ;-)
The wells Tripod not fall.
Perhaps it even rotating plate and with middle Zugsicherrung.
Would I connect rails / example. Flat metal strips s.schweissen.
The thing I respect the synonymous disconnect this connection can pack up.
Train or sliding fit options, so I thing can be pushed or pulled.
That should be his first.
MfG
B. DeKid Hy B. DeKid,
thank you for your ideas. The idea with the Zugmöglichkeit I had already synonymous, and I think I will implement the aufjedenfall.
That I must connect the rails, is synonymous aufjedenfall a good tip. Unfortunately, I have, for technical reasons, currently not a possibility, and a simpler alternative for me as just not synonymous.
What do you mean as I get attached s.besten Tripod? Should I drill small recesses inside, or how it is s.besten?
But I think for a first DIY, I can quite satisfied.
Many greetings,
Moritzk
Antwort von B.DeKid:
Gude
Yes either wells or more plate with 3 holes, or shallow aufgeschraubte of caps such as spray cans or bottles.
Centered a carbine, this via GummiSpanngurt with the center column lock.
If you're technically not a machine you take Strong Velcro and glue. Each on the underside of the small pieces of pipe sticking. The pieces against the topside of the metal strip, should be synonymous fold.
MfG
B. DeKid
Antwort von Moritzk:
Gude
Yes either wells or more plate with 3 holes, or shallow aufgeschraubte of caps such as spray cans or bottles.
Centered a carbine, this via GummiSpanngurt with the center column lock.
If you're technically not a machine you take Strong Velcro and glue. Each on the underside of the small pieces of pipe sticking. The pieces against the topside of the metal strip, should be synonymous fold.
MfG
B. DeKid The idea with the carbine I like quite well, but the idea with the caps of the bottles synonymous werd :-) I'll see what can be implemented s.besten.
The thing with the rails on the other hand, sounds to me after a rather wobbly affair. I think because I will rather wait until Easter, and then a welding mögklichkeit in the home use :-)
Right rails are stable, I think the most important thing for a quiet recording.
What say you actually like the roles I've fixed? Often, the roles of other modeler so rather obliquely, which was synonymous, I think has its advantages.
Antwort von B.DeKid:
Sure oblique roll by, you have more surface.
Quasi offers a 3er kombi s.1x top 2x Side.
While rails should be stiff, but should be Velcro in the case (weight) quite rich (! Come to the Velcro strip to!)
(! And the usable Aulagenfläche!)
;-) Yes lids are good for something ;-) Hab synonymous already provesorisch I used s.zB. Halfpipes ;-)
= Carbine idea because I've such a tripod that has ne centered eyelet (cheap thing) because s.Hang below (MTB) was unsure of the thing, I've NEN tent floor Herimg anything done and NEN AutoSpannGummiGurt intervening tense. (The rubber strap was too long simply knotted loop inside) The thing was then determined s.Ort clean and place.
Do not always have the latest most expensive, we must do is tinker, then adjusts the already ;-)
Well for the guys I am anyway since childhood days MacGyver,'ve always synonymous tions "Today, so-called" multi-tool s.Start,-p
I find it good when someone searches for solutions and ready synonymous is time to invest initially and leading to tinker.
Do what my dollies are ;-)
Inline skates, skateboard, bike trailers, Kettcar clean and it works well ;-)
(The Kettcar is geil! Can U profiles to run when desired, can s.Rohrrahmen clamp recordings tripod mount, you pillion seat - a true "mountain" halt)
MfG
B, DeKid
PS: The pushing things - and each eyelet rods Recording (see drawer or small trailers) I would suggest.
