Frage von axel hundrages:
Hello
Who can tell me how to make a stamp with DigiBeta accurate timecode that the first picture starts at 01:00:00:00 and 00:58:30:00 eg when the test is so visual and so is this a "standard" Recorder of Sonyrum. What you have to press buttons? :)
dankeeee
Antwort von BjörnF:
Also, the buttons will hopefully still find themselves, if they are synonymous to some extent under the flap.
But with clever nem coded Sendeband the program starts at 10:00:00:00, and not at 01 :....
Björn
Antwort von hombre:
And then tape 2 starts at 20:00:00:00?
Antwort von Axel Rogge:
Hello
Who can tell me how to make a stamp with DigiBeta accurate timecode that the first picture starts at 01:00:00:00 and 00:58:30:00 eg when the test is so visual and so is this a "standard" Recorder of Sonyrum. What you have to press buttons? :)
dankeeee Ok, I'd try from memory. TC-generatur on preset nciht under the flap to free run (or preset? Thing, red). Then (glaubich) set, reset, next to the time code zeroes the display, then the jog dial to adjust with time (59:58:00) and SET drücken.dann assemble and record.
Or with a cutting management will be a 1st Edit, reçine 1:00:00:00.
Check it!
Axel
Antwort von mdb:
And then tape 2 starts at 20:00:00:00? If the mission is longer than 105 minutes ...
Joking aside, usually, each Sendeband starts at 10:00:00:00. The tapes present in the correct order is then sometimes synonymous my job.
Antwort von veit weitwinkl:
hm, why then even notice the first two digits are always the same when so eeh? It will not happen very often, footage that is spread across several tapes. And then they should all begin with 10? what does it make sense?
Antwort von mdb:
The difference between the footage and is Sendeband but you know?
Rotational bands begin at home with xx: 00:00:00, where xx is the current tape number is (which then was at the shoot with more than 24 cartridges uncommon) problems
Antwort von axel hundrages:
Hello mdb
no, I'm not really the idea. Therefore, thank you for the explanation! Why is it that transmission bands with 10 to start? Has any (deeper) sense?
Or with a cutting management will be a 1st Edit, reçine 1:00:00:00.
Check it!
Axel How exactly does that? I want to play a movie from Avid. How do I get the first frame of the film exactly on the TC 10:00:00:01?
(yes you have to play and recording) simultaneously start. Which device is controlled Of whom?
dankeeee
Antwort von BjörnF:
The origin of this? No clue - Is halt so :-)
Turning cassettes halt with 01, 02, etc., and master / stop transmission bands with 10:00:00:00.
Just take the first frame, much depends of your individual configuration - the basic prerequisite is that you actually can control the VTR with the calculator, or you need to have two very synchronous hands :-)
Björn
Antwort von ostiii:
Why is this: That I can say. So - (with old editing systems as synonymous now) at the new of it is not possible to come lower than the TC: 00:00:00:00 - because that would be then 23: xx: xx: xx. But since there are programs which are longer than one hour a starting timecode of 01:00:00:00 was not advantageous. Why go to all stations (except Pro.7 and ZDF), the transmission bands at 10:00:00:00. Advantage: It can be immediately read off how long is the contribution. In ZDF and PRO7 the transmission bands starts at a 00:02:00:00 - while one must always be aware of 2 minutes deducted read.
Antwort von Axel Rogge:
How exactly does that? I want to play a movie from Avid. How do I get the first frame of the film exactly on the TC 10:00:00:01?
(yes you have to play and recording) simultaneously start. Which device is controlled Of whom?
dankeeee Interesting approach, but difficult to make .... :-)
At Avid, the issue is, on tape "Digital Cut". In the next window, you can choose whether you) to sequence-Time (TC = TC tape sequence, or want to play Mark-in. If you're not on Avid at home - good luck.
Axel Rogge
Antwort von prem:
Interesting approach, but difficult to make .... :-)
I thought so:) Kenn this "technique" or first cut of my experiments with 2 VCRs:)
At Avid, the issue is, on tape "Digital Cut". In the next window, you can choose whether you) to sequence-Time (TC = TC tape sequence, or want to play Mark-in.
Axel Rogge Thanks, that helps very schonmal. Tomorrow Shall I just try it.
If you're not on Avid at home - good luck.
Axel Rogge Thanks, I'll need:)
Antwort von axel hundrages:
so, I once again:)
Unfortunately the whole thing does not work yet so true. Although controlled from Avid I can play on and off my DigiBeta, but he somehow takes "to put".
So I wanted to record 1 minutes, starting at TC 09:58:30:00.
I have the body with corresponding IN and OUT marks in my timeline, digital cut open, "Record Time Desk" is selected (was that right?), Entered the starting time code and pressed the red PLAY button.
It is synonymous everything goes so far that not only the tape of me jumping on the desired TC before the recording starts. After recording, then something else is synonymous in the corresponding fields at IN and OUT, see screenshot
http://img164.imageshack.us/my.php?image=digitalcutjh7.jpg
What am I doing wrong?
Dankeeeee
axel
Antwort von jpsaenz:
"instead of mark in" Record Time Desk "is somehow better:-D
Antwort von prem:
but still ask one.
what if the tape still does not have a TC? Simply vorkodieren the first few minutes? But what's with the OUT-point, the Avid is yes then no?
dankeeee
Antwort von adrianmpc:
Hello,
ok, now I'm standing right in front of this issue. The tape is not until the end of the pre-encoded and DigitalCut the recording breaks off s.der point where the TC stops on the tape. What do I have to press buttons or pass on what lever? :)
Sorry, got true 0 idea of playing off the decks: (
Dankeeeee
Antwort von adrianmpc:
Hello,
ok, now I'm standing right in front of this issue. The tape is not until the end of the pre-encoded and DigitalCut the recording breaks off s.der point where the TC stops on the tape. What do I have to press buttons or pass on what lever? :)
Sorry, got true 0 idea of playing off the decks: (
Dankeeeee I can only hope that you're asking for your work no money ...
"Assemble" as Schnittart for uncoded tapes and NOT insert ...
And here are the "one million U.S. dollars Clue":
In the AVID Settings "Allow Assemble Edit activate, otherwise geht's nich ...
Stef.
