Frage von popaj:Hi All,
where do I get the software for my GS500 on Vista
run it.
Have now switched to Vista and just stress!
Firewire cable on it, but do nothing themselves. No connection.
Synonymous but he recognizes the Cam Vista not.
What to do?
Thank you.
Antwort von Alf_300:
A little more info would not be bad
Power off
All CAM settings checked?
GS500 and Win7 Premiere via FireWire and is making me any problems
Antwort von popaj:
Hi,
So Cam is s.Netzteil.
Connected over Firewire.
What do you mean DV settings, s.der Cam.
I changed nothing, has remained as s.alten Calculator.
Where it made it work with XP without problems.
Wanted this install included Cd, it might not work.
Is only for Win2000 and XP.
Antwort von Alf_300:
PSU would really rich
Einstöpsel and then ought to
Found New Hardware Wizard in Control Panel are ind
Panasonic DV camcorder
Antwort von popaj:
hmmm,
have again joined s.alten Calculator, I get there somehow synonymous is no connection.
What is it now?
Firewire cable?
Otherwise Ching synonymous forever.
Antwort von Alf_300:
Defective Firewire cable or poor contact can be
Otherwise, I tried again grad
GS500 + Win7 x64 Premiere CS4
not the slightest problem
Cam is recognized in all settings
For capturing one must halt Play Set
If I have time, I can still test vielleich synonymous with VISA
But do not believe that there is a difference.
Antwort von popaj:
Have the dates updated my XP to SP3, it might be synonymous
it be?
Well, yes, but on the new läufts not synonymous.
I had brought from his old neighbors Firewire cable,
synonymous, but not better. I hope my computer is connecting
not flat.
Thank you.
Antwort von Alf_300:
I can tell from my Page
If the interface in the Control Panel there is as it should work with USB Win7, Vista Sp2, Xp sp3,
Schieint to act thus a hardware problem.
Antwort von popaj:
Hi,
Thank you.
Well it came today of tomorrow.
Otherwise, the cam always super detected. Yes is probably
be a hardware failure. This IEEE .. Interface
is detected. So then probably cable or DV output?
I have the cable borrowed from neighbors, but has been synonymous
a little older like mine. 'm Going today to buy a new cable
go. If that is not synonymous then goes is probably the DV-output flat.
But I always respected that I was on it before earth, before I
connect it, funny. Or it may be a general deterioration of the connection?
Hopefully it is not expensive.
Antwort von popaj:
Good evening,
it was just in the store at times the DV port to test.
That probably seems to be the reason.
So, in good German, who is there (flat).
What now?
Repair? Cost?
Can I transfer an X for any Mini Dv Camcorders
? take? From the low price range?
Or is the quality flutes??
Thank you.
Antwort von Alf_300:
Until the cause is not clear, you should get is synonymous ij future a new / additional interface.
Otherwise you must know yourself as the CAM is in good shape and if you you need in the future or to switch to one of the new.
A request from Panasonic can not hurt, otherwise an Other DV-Cam is synonymous.
Antwort von popaj:
Thank you very much.
Did the Cam always handled with care.
When combined with the Firewirekabe in the DV jack, I have
always grounded. Always with caution.
Could it possibly the last time I've filmed on snow and possibly
a drop of water has got in??
Of course, I would like to use the Cam next, is about 3 years old,
but except for the DV-output even top!
On Pc s.einer On board was the cable interface, so no extra
Firewire card.
I Will probably still get a smaller (from the NV-GS series) and with this can only be transferred to the PC, s.besten constantly connected. So very small as NV-DS 60 would go synonymous? Or would rather have a GS150-GS320?
I read somewhere that someone is a pan. Repair X500 for 70 ¬ was, even though it is similar to the GS500er right?
Antwort von Alf_300:
Why sometimes the firewire breaks is not traceable at least to me, because I've never really watched.
But, now, nothing more synonymous Helps
Email s.Panasonic service - what does it cost or dealer (of course, his expenses extra.)