Frage von Yawner:
Hi
When video editing program Sony Movie Editor is the Sony Capture program here. Now I have full first quarter tape captured, which went only as far as synonymous with over 200 frames dropped, I found something "unopitmal". Where Sogut. When you name the other full tape interestingly he breaks sometime, ie a few times just ran the preview no longer with the clips and were included in the project media no longer appear, however, were on the hard drive in place, and another came ne stupid error about 45min ..
The material is very normal 16:9 widescreen PAL. Is there something to note when I capture? With another (stupid me did not like) tool I've captured the whole tape with a lot less dropped frames. The tool beherscht the scene detection is not really. The Sceneylziyer (irgendwie so ^ ^) I will not buy me, and 4 Different Programs only to finally aufm PC my material I will have to be synonymous not actually use.
Gibts nen tip as I though of bringing Sonyzum work? Virus scanner, Internet connection and the whole stuff was all out. Do not synonymous side made. NEN Calculator is AMD Sempron 3000 with 512MB Ram.
Greeting
Yawn
Antwort von TMaekler:
Irgenwas but it must have disturbed when capturing - otherwise would not be this high number of droped frames occurred. For good video editing systems are 0 droped frames usual!
Antwort von Marco:
Do you maybe not movie editor, but Movie Studio? When contained capture program is quite a scene automatic separation possible during the capture, only synonymous in the settings enabled.
With this capture tool I have been doing years capturing and basically never had a single Dropped Frame. Da stimmt was definitely not with your system.
Marco
Antwort von Yawner:
Thanks for the help!
my course I use the Movie Studio ^ ^, I always confuse ..
well clear of the integrated beherscht the scene :-) separation, which I really meant not synonymous ... probably have the word "other" overlooked .. ^ ^ naja macht ja nix.
@ Guest: Well if I have my system as good Videoschnitsystem would describe .. :-) Less .. but still too many lost frames ..
@ Marco
hast du mir NEN tip my system with what is wrong? Thus I use the "Optimize" can
Greeting
Yawn
Antwort von Marco:
Which hard drive or partition which you have captured the material?
Marco
Antwort von Yawner:
to the non-system partition ^ ^
I now probiers again without the record of the statues. Can you give me vll. otherwise your settings?
Should I make custom frames? Previously, I had 25.00 but now I'll let the tick away ..
Greeting
Yawn, now just hours away ne ^ ^
Antwort von Marco:
Yes, but what harddrive is it? Do you have only one in use on the various partitions are set up?
What are the settings, I would simply leave the default settings.
Do you have any lasting Preview enforced? Then turn off the preview of the Capture tool.
Marco
Antwort von Yawner:
I have the preview turned off permanently, and since I had 29.97 frames set I've converted ..
I have only one hard drive with 5 partitions .. 2 of them are for Linux, Dos and 1 for the remaining 2 are for Windows ..
As already written, I always capture the "non-system partition"
Moreover ichs've now captured, I always sat next to it and once the program is verreckt I s.Camcorders ended. The whole was just a little hectic because everywhere must go very quickly because otherwise the material is practically "disappears"
Well something really fun course not .. grmbbrmbl ..
Greeting
Yawn
Antwort von Marco:
Take a second (external) hard drive, via Firewire or USB2.0 connection.
Marco
Antwort von AndreasBloechl:
Times I had similar problems with Vegas 5 and my old calculator. If there a certain place s.der second plate (Video Disk) was described, I had DropFrames if I but then the plate was completely cleaned up so that this body was not described were without DropFrames. I have the error for a month until I sought out was me. Perhaps it is when you really synonymous to the plate with the letter is not the case.
But what I did think of, delete all times Temp folder and defragment all disks times befor you start with the capture.
Antwort von Yawner:
Thanks for the tips! If yes really fast!
External FP exists, I've just not tried because of NEN buddy told me that he always hung the system when he has it on his external capturet.
Well I voted IDE but more than 3.6MB per second, but will hopefully create :-)
The Tempordner Incidentally, I had emptied synonymous extra (CC Cleaner and "1Klick Maintenance")
Defragment I could still try, just as always it takes forever ....
But thanks for the help, I am now such times NEN external prog to defragment ^ ^
Greeting
Yawn
With the above method, I had in fact synonymous lots Dropped Frames. Interestingly opens after capturing always this window again when everything important Drinsteht and whether you want to delete this now, etc. The values or there drinstehen about Dropped frames are never the same as we have seen during capturing .. ..
Nen update for the prog, I have not synonymous found, one can under Help -> Sonyim Web -> Update for Sony Video Capture 6 Sun ne site with its quantity of updates, but then I have found nothing ..
Antwort von AndreasBloechl:
The plates are already on UltraDMA mode?
Have you ever synonymous start the car and cleaned out everything what is not needed.
Antwort von Yawner:
yes my car start up of the things I want to really empty ..
says at least my mconfig (are there enough remote checkmark ^ ^)
ömpf UltraDMA mode I have never heard of, can I somehow look? But I guess times already ..
Greeting
Yawn
Antwort von AndreasBloechl:
Yes you need to be in the device manager the IDE primary and seconda dial and see if the UDM is set.
Antwort von Yawner:
s.ok is terminated. "Even" the 6er. :-)
That means it is s.was others? Grmblbrmbl ..
Greeting
Yawn
Antwort von AndreasBloechl:
Then I really know is no longer synonymous next. But I would be times in the capture module of the Vegas setting it at DropFrames stop with the capture so you can accurately s.wann times by the plate is no longer with the store mitkommt.
Antwort von Yawner:
So thank you again for all the answers! It will probably sometime but NEN new system is due ..
joa that with the Dropped frames -> Exit vll. would not be bad, but then I would be busy the whole time ^ ^
Greeting
Yawn
