Frage von Niklas_Hamburg:
Hey,
I do not know what has happened dismissed, but I've lost my Velbon DV -7000 with the screw that holds together the swiveling head (; say when the missing may be found in the swiveling head) watching
I can buy somewhere alone or must I get right back now the whole head?
Antwort von KSProduction:
Hey,
I do not know what has happened dismissed, but I've lost my Velbon DV -7000 with the screw that holds together the swiveling head (; say when the missing may be found in the swiveling head) watching
I can buy somewhere alone or must I get right back now the whole head? no, you do not have to! s.velbon you can write the answer synonymous, I know from personal experience.
is one of the screws, the screws are like wings, plastic grip so with the Turn to? where the upper s.schwenkkopf looks exactly the same as the bottom? But achtung, which both have a different thread!
which of them is missing, up or down?
Alternatively, you can circle of acquaintances to nem mechanic (; werkzeugmacher, locksmith, mechanic) to go can tell what you need, there is someone like that with you?
Antwort von Pillermännchen:
Presumably you do not have the central screw holding the head on the tripod.
The one should stick with a new DV7000 anyhow, because the pan comes loose again. Was synonymous here already subject.
To the screw itself, I do not know anything and can not synonymous ..... check mine is stuck. ;)
But I seem to recall that synonymous inch thread had.
Jens
Antwort von KSProduction:
Presumably you do not have the central screw holding the head on the tripod.
The one should stick with a new DV7000 anyhow, because the pan comes loose again. Was synonymous here already subject.
To the screw itself, I do not know anything and can not synonymous ..... check mine is stuck. ;)
But I seem to recall that synonymous inch thread had.
Jens So I think it's not at all. you lose without screws glued s.DV7000 not such a simple screw. habs I just looked again. I still is not even clear what he thinks screw. So swing through alone because you lose nothing. rather then when the screw is badly wide open the tripod in the suitcase and it "throws" s.end. I can not understand, sorry!
Antwort von Niklas_Hamburg:
has therefore been suggested as jens really do not have the screw, the zusamenhält the whole tripod head.
without the stop nothings is happening more.
Velbon just come from Japan, right? Have you then s.den Customer written?
Edit: So I grad again look to see of the outside is not at a screw visible.
http://www.abitus.pl/sklep/imgprd/galerie/dv7000/allegro_gora.jpg
In the picture below in the middle you can see it very well. It is this "screw" with one of the "can adjust tension adjustion", ie the head which can rotate more slowly.
I could not at check bust out like that ...
Here mans looks even better: http://aukcje.fripers.pl/velbon/dv7000/dv7000_10.jpg
Antwort von Pillermännchen:
This is not the synonymous screw that I meant.
Those things, which you addressed, when screwing generate pressure, which then slows down by friction, the head movement.
Whereas I thought the screw that you can now see through the hole and which is the vertical axis of rotation of the head.
Have I just seen again.
Except for the screw you will still not be the metal fork, which acts on the thick shaft inside.
Neither the nor the adjuster will you get in the hardware trade.
Then you will really only Velbon.
: edit:
Look here:
http://forum.slashcam.de/deffektes-velbon-7000-vt69585.html
Jens
Antwort von KSProduction:
has therefore been suggested as jens really do not have the screw, the zusamenhält the whole tripod head.
without the stop nothings is happening more.
Velbon just come from Japan, right? Have you then s.den Customer written?
Edit: So I grad again look to see of the outside is not at a screw visible.
http://www.abitus.pl/sklep/imgprd/galerie/dv7000/allegro_gora.jpg
In the picture below in the middle you can see it very well. It is this "screw" with one of the "can adjust tension adjustion", ie the head which can rotate more slowly.
I could not at check bust out like that ...
Here mans looks even better: http://aukcje.fripers.pl/velbon/dv7000/dv7000_10.jpg http://www.velbon-shop.de/
yes then the damping screw them. which of course is relatively short and designed so that one can compensate for temperature fluctuations in the game a bit. a matter of feeling .... you must Dispensing is the really not very far because the associated wing so synonymous adjusting screw still leaves something to be open.
Antwort von KSProduction:
has therefore been suggested as jens really do not have the screw, the zusamenhält the whole tripod head.
without the stop nothings is happening more.
Velbon just come from Japan, right? Have you then s.den Customer written?
Edit: So I grad again look to see of the outside is not at a screw visible.
http://www.abitus.pl/sklep/imgprd/galerie/dv7000/allegro_gora.jpg
In the picture below in the middle you can see it very well. It is this "screw" with one of the "can adjust tension adjustion", ie the head which can rotate more slowly.
I could not at check bust out like that ...
Here mans looks even better: http://aukcje.fripers.pl/velbon/dv7000/dv7000_10.jpg Here you get the Velbon Part:
http://www.velbon-shop.de/
And here the addy in japan where I wrote back then German one, what a surprise :-) is
support@velbon.com
wish you good luck
