Frage von anne123:
Hi,
I have a problem with the video transitions. Between some clips I can not change the duration of the transition. It is auto set to 0.01 seconds. I want to connect two mov files. When I pull apart do I put on every single synonymous for a long transition, but just not when they are connected ...
Thank you and best regards, Anne
Antwort von Pianist:
Have you been s.end of the first and the second clip s.Anfang enough food for Aperture? Otherwise, just the first clip and rear clip on the second take forward a few frames to the then as feed have. It may be synonymous, that has got you by mistake between the two clips a single foreign Picture, look again with the greatest magnification.
Matthias
Antwort von anne123:
Thanks for the quick reply.
What do you mean with food? I have watched with the greatest magnification, images are not in between. I have been synonymous for a few frames (front and rear) away, but it still does not work ...
Antwort von Pianist:
Strange, one other assumption I have not. But to your question: If you hintereinandersetzt two clips, where the Outpunkt of the first clip, the very last picture and the Inpunkt of the second clip, the first picture is absolute, then there is nothing you can use to fade. Consequently, one would have to make a long ten images fade, away from the end of the first and second clip from the beginning of each of five images, so it works. These overlaps are editors of "food called".
Matthias
Antwort von B.DeKid:
With food, he says - the one synonymous transition effect must have enough frames to be used.
In practice, this means about 1 1 / 2 sec s.end clip A and 1 1 / 2 sec clip of s.Anfang B (eg) = Effect of Blend can take 3 sec.
.........
Are the clips A + B may be too short in part, some transitions are generated.
MfG
B. DeKid
Double gemoppelt post - sorry it was faster.
Antwort von domain:
Feed means that the average first time, not all frames are utilized that are present in reality. If you let antoßen the last original frame of the first clip directly s.den first frame of the next, then neither one-sided overlap or Hineinverlängern one of the first clip in the second, still a Rückwärtseinblenden of the second clip in the first possible.
Antwort von srone:
With food, he says - the one synonymous transition effect must have enough frames to be used.
In practice, this means about 1 1 / 2 sec s.end clip A and 1 1 / 2 sec clip of s.Anfang B (eg) = Effect of Blend can take 3 sec. But this is not entirely correct about the glare effect can then be only 1.5 sec long since I need two clips for it.
lg
SRone
Antwort von domain:
So the word food is a trigger for us gallants ;-)
Three replied almost simultaneously. I'm going feed.
Antwort von anne123:
ok, that with the diet I've seen. My first clip is about 9 sec, the second 5 seconds long. So I really should have no problems or add a 1sekundenlangen transition?
Antwort von srone:
The clips should be 1s overlap.
lg
SRone
Antwort von Debonnaire:
Mann makes it here once again overly Erklärerei ne!
To crossfade clips, they have to (for example, on two superimposed video tracks) at least the length of the planned transition overlap.
Have you no more frames available, because you already s.end of the first and the second clip s.Anfang are, you can not fade. Basta and ready!
Antwort von domain:
When trimming the clips, I never start directly with the first frame, but looking times when the picture has calmed down immediately after turning the camera, just as when setting the end marker. So are the trimmed clips almost never as long as the original clips. This "aperture meat" can also be used for subsequent transitions quite yet, because in the beginning of a transition in any case hardly recognizable. So be sure your clips are not 5 and 9 seconds (without fading).
Basta and finished (s.uncharmanten Débonnaire).
