Frage von Tommy122:
I think I'm at a RODE NTG-1 to create and would take a short XLR cable!
Share everywhere only 1m cable and these are much too long!
The shorter the better!
Maybe you have a good source!
Antwort von Kino:
For example: http://www.thomann.de/de/the_sssnake_sk23303_xlr_patch.htm
Antwort von Tommy122:
Thank you!
Just ordered! :)
Antwort von Festivaldrummer:
Experience shows that you had really better 4 ¬ pay more. But well now it's author as well as too late.
http://www.thomann.de/de/cordial_cfm_05_fm_sw.htm?sid=2b85c2baa16cd45fd5f83091333d2bd8
Antwort von Tommy122:
Experience shows that you had really better 4 ¬ pay more. But well now it's author as well as too late.
http://www.thomann.de/de/cordial_cfm_05_fm_sw.htm?sid=2b85c2baa16cd45fd5f83091333d2bd8 Why?
fits the other not?
Antwort von Tommy122:
@ Drummer Festival
fits is not easy ?????
Antwort von Videobodo:
Hello
I enjoy my music-dealer the required short cable. I usually need to pay only for the times, the 50cm string free there.
Bodo
Antwort von techman:
No fear of fit, it does.
I think fears Drummer Festival, the quality of noname XLR-Male is not good and it will not last very long - that he finds the times of Neutrik Cordial cable quality. I find that although synonymous and buy really only Neutrik, but you can use so as long as it goes, and when it is out is a new, buy (better).
Antwort von Tommy122:
Can you tell me maybe a little to the setting?
The reason for me was to buy an external micro I of this extreme noise of the original Micro's not like it!
I've filmed on a yacht and had constant noise of this engine in addition to the voices in the sound! Although the engine of the yacht was far away!
Used it the high-pass filter? XLR MIC ATT - OFF or ON?
And the gain setting in the menu? Without or with?
Antwort von xandix:
The reason for me was to buy an external micro I of this extreme noise of the original Micro's not like it!
I've filmed on a yacht and had constant noise of this engine in addition to the voices in the sound! Although the engine of the yacht was far away!
I myself have a white and XHA1 and a NTG1 the problem.
At the point where the micro-holder is you start with you EVERY Microphone sounds of the motor drive.
Even with a Sennheiser MKH416 (tried out).
The Micro has the accessory shoe on it.
Enclosed is a picture of me with Sennheiser MKH416.
Greetings
Antwort von Tommy122:
@ Xandix
Thank you for your answer!
you me at your settings using? you open at the bottom?
Aufnhame of Mono on CH1 and CH2?
Do you use the high pass filter? XLR MIC ATT - OFF or ON?
And the gain setting in the menu? Without or with?
Antwort von alpenmolch:
Have exactly this "cheaper" XLR (0.3 m) cable with the RODE NTG of Thomann-1 s.meiner HMC-151.
-Perfect-
greetz
ecki
Antwort von xandix:
you me at your settings using? you open at the bottom?
Did you have a gray filter on the lens?
Aufnhame of Mono on CH1 and CH2?
yes.
Do you use the high pass filter?
No, because my mic holder is decoupled. If not with you is decoupled, then yes.
XLR MIC ATT - OFF or ON?
Depends on the environment from noise.
If it is noisy and provides a MKH416 synonymous NTG1 a (not quite as much) so many levels that the Mic ATT makes sense.
Greetings
Antwort von Tommy122:
No, because my mic holder is decoupled. If not with you is decoupled, then yes ...............
what exactly do you mean?
Antwort von xandix:
No, because my mic holder is decoupled. If not with you is decoupled, then yes ...............
what exactly do you mean? This support is decoupled:
http://www.thomann.de/de/rycote_invision_inv7.htm
NOT this:
http://www.thomann.de/de/the_tbone_mikrohalterung_s.htm
Difference clear?
Greetings
Antwort von Tommy122:
Neither .... I use it directly on XH A1
Antwort von Daniel007:
Does that mean that I should generally screw mics such as Sennheiser ME 66, Rode NTG 1 or 2 and even Sennheiser 416 on the accessory shoe?
Antwort von xandix:
Neither .... I use it directly on XH A1 Just so you so you start your engine noise are:
First, because your micro is not decoupled DC and secondly s.Kameramikrohalter (wrong space agency, s.der engine noise to hear even more clearly) is fixed and is not above the shoe on the camera accessory.
Greetings
Antwort von xandix:
Does that mean that I should generally screw mics such as Sennheiser ME 66, Rode NTG 1 or 2 and even Sennheiser 416 on the accessory shoe? Yes, exactly.
Only because the engine noise is not heard.
The next away, the better!
Greetings
Antwort von Daniel007:
Does that mean that I should generally screw mics such as Sennheiser ME 66, Rode NTG 1 or 2 and even Sennheiser 416 on the accessory shoe?
Yes, exactly.
Only because the engine noise is not heard.
The next away, the better!
Greetings But what do I do if I want additional installation of a video light?
Antwort von xandix:
Does that mean that I should generally screw mics such as Sennheiser ME 66, Rode NTG 1 or 2 and even Sennheiser 416 on the accessory shoe?
Yes, exactly.
Only because the engine noise is not heard.
The next away, the better!
Greetings
But what do I do if I want additional installation of a video light? Then you have a problem!
Maybe something like that?
http://www.foto-walser.biz/shop/Artikel/2419/531/Sonstiges_Blitz_Zubehoer_walimex_Klapp_Blitzschiene_mit_TELESKOP_Arm.htm
Greetings
Antwort von Daniel007:
Does that mean that I should generally screw mics such as Sennheiser ME 66, Rode NTG 1 or 2 and even Sennheiser 416 on the accessory shoe?
Yes, exactly.
Only because the engine noise is not heard.
The next away, the better!
Greetings
But what do I do if I want additional installation of a video light?
Then you have a problem!
Maybe something like that?
http://www.foto-walser.biz/shop/Artikel/2419/531/Sonstiges_Blitz_Zubehoer_walimex_Klapp_Blitzschiene_mit_TELESKOP_Arm.htm
Greetings Are you sure that the engine noise with the right? It has never been a mention of them was in any way.
The other problem is the decoupling. The NTG 2 is not so isolated. What am I doing here? Microphones are s.den the microphone holder actually decoupled at all?
Antwort von Tommy122:
Perhaps to rectify again !!!!!!!!!!!!!!
I thought with the engine noise of the motor yacht!
The drive is not listening to me absolutely!
Do I still activate the high pass filter?
Antwort von Videobodo:
I think anyone here is totally beside the hat!
Bodo
Antwort von xandix:
The drive is not listening to me absolutely!
Then say it and do not let me bring endless examples of "actions against drive noise" that does not really interest you!
I thought with the engine noise of the motor yacht!
Do I still activate the high pass filter? If you like the sound of the motor yacht at the moment even hear (so you with your own ears), of course, synonymous songwriter on top of the Micro.
You can soften the sound by adding it to the target with micro-point away from the engine (so directional in the other direction to position the boat engine).
To remove boat motor noise from a recording is more necessary than a high-pass filter. Since you have in post production dig deeper into their bag of tricks, because the frequency spectrum of engine noise not only includes bass parts.
Greetings
Antwort von Bernd E.:
... Does that mean that in general I should screw on mics ... the accessory shoe? ... You can use them synonymous with an adapter like the
SM5 of Røde
Antwort von xandix:
... Does that mean that in general I should screw on mics ... the accessory shoe? ...
You can use them synonymous with an adapter like the SM5 of Røde decouple from the camera body, if the camcorder has a microphone support side. Then there is the accessory shoe free for other things. Available here for affordable Money:
http://www.thomann.de/de/rode_sm5.htm
Greetings
Antwort von Daniel007:
... Does that mean that in general I should screw on mics ... the accessory shoe? ...
You can use them synonymous with an adapter like the SM5 of Røde decouple from the camera body, if the camcorder has a microphone support side. Then there is the accessory shoe free for other things. But now I wonder: yes microphones can not be decoupled sogesehen. So we speak of a decoupled Microphone, if the mounting is isolated? The lateral support of the XH-A1 that's something. What's in it now, this dranzuschrauben SM5 additionally?
Antwort von xandix:
But now I wonder: yes microphones can not be decoupled sogesehen. So we speak of a decoupled Microphone, if the mounting is isolated? The lateral support of the XH-A1 that's something. What's in it now, this dranzuschrauben SM5 additionally? so what does the SM5.
The decoupling XHA1-holder (ie the elongated rubber parts inside) is not working.
The gum is only there that (one of the diameter) suitable micro stuck in there nicely. To do anything else .... but he is no
Greetings
Antwort von Daniel007:
But in general you can not uncouple itself mics but turn to build either a relative support as in VideoMic or SM5 or one decouples the bracket. In both cases we speak of but then falsely decoupled microphones. Correct so far?
Antwort von Bernd E.:
So ... It speaks of a decoupled Microphone, if the holder is uncoupled? ... The mount decouples the microphone from the camera body - or not synonymous, depending on how complicated the holder is constructed. The best effect, the so-called "spider", which is the Microphone of crossed rubber bands held.
... The lateral support of the XH-A1 is already something. What's in it now, this dranzuschrauben SM5 additionally ... The first, a better decoupling takes spider because of the construction and the second it moves the microphone off of something next to the optical axis, thus reducing the risks of having the windshield in the picture. And finally, the spider has been synonymous well the mics that are too thin to sit directly in the holder of the XH-A1.
Antwort von Tommy122:
So I tested just once with the habs XLR MIC ACC ON!
There must, however, extremely loud so you need the time!
The sound is indeed almost as quietly as that!
What exactly is the advantage of the ACC switch?
could indeed synonymous adjust the level manually by the rotating wheels?
And what is the gain of the audio which you can set in the menu?
The same again? just the level down?
Antwort von Videobodo:
Hello Tommy
Leave it better, look for a less demanding job than the movies.
Bodo
Antwort von Tommy122:
ne very armseelig answer! ;)
Antwort von Videobodo:
But after your question correctly.
Bodo
PS: You should at least be able to express his problem, then they will be helped.
Even for functions such as gain, etc, it is of advantage to know what happened there when you have such a cam at his disposal.
Also, the hammer, it is important to know where the front is.
Antwort von Tommy122:
I know what gain does with cameras!
However, I am never up to now with microphones working because I did not need the sound up now!
I'd just like to know one thing ...... it is possible with the XH A1 and the NTG-1, the micro adjust so that it takes up less extreme noise as possible but only takes in the direction of where to film!
Antwort von Daniel007:
"In the direction where you film ..."
Well, the NTG will certainly not only the front of the micro but synonymous of everywhere else. Synonymous never heard of have a microphone that makes it differently. You can use the adapter of Rode SM5. This decouples the microphone and at the same time it is not quite as close s.Laufwerk.
Antwort von Tommy122:
So said in good German ...... NO!!
And because of the drive, the problem I have not!
I have absolutely no drive noise in the sound!
Antwort von Daniel007:
I think not synonymous, that you should imagine it as loud. So loud it is in fact not likely to hear synonymous. When will the rather minimal "noise" to be. But this is not my area, because I myself have never had these problems. Listen quietly to the times by his colleagues.
When I look at your spelling and punctuation look like that, I inevitably ask myself how old are you - if I may ask for. ;)
Antwort von Tommy122:
haha
Not s.meiner grammar doubts!!)
I am an Austrian from Vienna, I have a slightly different vocabulary and spelling ne others like her:)
By the way I'm 30!
Antwort von Daniel007:
Okay, all taken back! ;)
The many exclamation points and "highlight words" made me wash the ask. :)
Antwort von Bernd E.:
... The NTG will certainly not only the front of the micro but synonymous of anywhere else in ... If this were so, it would not be so many different types of microphones. Of course, there are very major differences which is the direction from which the sound is strong, weak or not received. Which is described by the so-called "characteristic" of the microphone: http://www.movie-college.de/filmschule/ton/richtcharakteristik.htm. The NTG-1 / 2 is a super-cardioid and as such focuses quite strongly on the front of the sound. Why else would use it at all?
Antwort von Tommy122:
Thanks Daniel!
Exactly what I wanted to hear!
I think the original microphones of the XH A1 is a bullet!
